Mangrove Products: 4" Hydraulic Outboard Steering Lock, Steer Support for Outboard Boat Motors for Trailering and Transport Boating Accessories, Boat Motor Steering ST-Stops

Mangrove Products: ST-Stops provides additional protection to your outboard and boat when trailering. These are a great additional boat accessory item to pair with Mangrove Products transom saver line. The ST-Stops minimize stress and potential damage to your outboard hydraulic steering brackets, seals, bolt assembly mount, and/or piston/ram. We strive to provide an improved way of securing your outboard when in travel allowing for safe transport of your boat and outboard motor on your next fishing or boating trip. Our ST-Stops are marine grade set designed for optimal clearance and fitment when attaching to the hydraulic piston/ram. Our easy clip on function with our 10 inner locking grooves provides a secure fitment to a wide variety of hydraulic steering systems. How Put On: 1st center your outboard motor where the two hydraulic rams are equal in length on each side. 2nd Take your ST-Stop and push onto the hydraulic ram until snug in place. 3rd You are now ready to hit the road. How to Remove: 1st center your outboard where the two hydraulic rams are equal in length on each side. 2nd grab the sides of the ST-Stop with one hand pull up, this will dislodge the inner locking grooves. 3rd place in dry storage or boat hatch until its next use. Cleaning: Rinse with soap and water. Corrosion is not an issue with product as it does NOT use metal across entire product. Other Products we offer are Transom savers for outboard motors (Our TS-Block and TS-Pipe), Trolling motor stabilizer (Our TM-Stabilizer), and Our Reusable boat trash bags (BTB-Mesh and BTB-Full). Any boat with motor can benefit from our full outboard support and stabilization products. Other terms or names from the ST-Stops are hydraulic steering lock, steering column lock, hydraulic steering stabilizer, jon boat stabilizer, steering wheel lock, hydraulic cylinder stops, outboard steering stopper, outboard steering lock kit, Outboard steering wedge, boat motor stabilizer, boat motor support

• ✅SPECIFIC FITMENT: Our outboard steering locks fill fit 3/4 in. (19.05 mm), 25/32 in. (20 mm), and 7/8 in. (22.225 mm, NOTE: this size will fit very snug) hydraulic steering systems that utilize 4 inch rams. Compatible with Hydraulic Steering Brands include SeaStar, Protech, Silver Steer, and Uflex. NOT Compatible with Baystar, GoTech, and Vevor systems. Ensure each piston length is 4 in. when the outboard is centered for best fitment. Singular arm hydraulic systems are NOT compatible.
• ✅SUPERIOR SHOCK ABSORPTION: Using our Mangrove Products high compression rubber formula that we currently use on our transom savers for outboard motor and have now been integrated for your outboard engine steering stops to prevent violent sideways motion and impact of the outboard's steering system when trailering both short and long distances.
• ✅MATERIAL DIFFERENCE: Using Mangrove Products proprietary material mixtures of internal EPDM rubber and outer liner of ABS/Polycarbonate ensures rigidity, strength, shock absorption, and functionality. Our rubber wedge is hard enough to mitigate deformity of rubber and soft enough to absorb shock and energy when compared to metal or plastic
• ✅INNER LOCKING GROOVES: Our internal 10 groove design allows a true lock to shaft and to ensure correct placement to piston when shock occurs during trailering. Our special formulated groove system accommodates fitment to 3 different shaft diameters.
• ✅OUTBOARD STEERING SUPPORT: Our outboard steering locks provide optimal securement and shock absorbing qualities that prevent bending of clips that could potential pop out of place. Our design ensures the locking steering stabilizer will stay secured and attached in the event of sudden impact when trailering your boat. Other versions have potential to bend or flex causing the support to pop out or deform.
• ✅EASY TO USE: Our outboard motor lock allows for simplistic placement to each of your 4 inch hydraulic steering rams. It is important to know that centering the outboard first, provides the easiest install process. Can be used with boats outboard hydraulic steering systems mounted to Yamaha, Suzuki, Mercury, Tohatsu and others.
• ✅EXTERNAL GRIP: Our textured grip design allows for an ergonomic feel that allows you to easily grab the steering stabilizer for placement and removal. The steering stabilizer is also small in size and can be placed in your dry box or hatches until its next use.
• ✅ENHANCED OUTER LINER: Our hybrid ABS/Polycarbonate outer liner supports rigidity and structural performance compared to others. Our outer liner also has a glow in the dark option for easier visibility during early morning and late night boat trailer launches at the ramp OR gloss black.
• ✅REDUCE OUTBOARD MOVEMENT: Using this improved system will keep your outboard motor steering cylinder centered during travel and will absorb the expected shock when trailering your boat. Our design allows movement to prevent seal damage while also preventing sideways motion of the outboard during travel.